Electrical Permit in Moore, OK — Cost, Requirements & Process
An electrical permit authorizes any modification to the permanent electrical system of a property inside Moore city limits. It is separate from the building permit and is reviewed under the 2017 National Electrical Code as adopted by Moore. Even on projects that already have an active building permit, most electrical work is pulled as a sub-permit and inspected independently.
The threshold is lower than most contractors realize. Installing a new circuit, replacing a service panel, adding a 240V outlet for an EV charger, swapping an electrical meter socket, or running new low-voltage HVAC control wiring all require a permit in Moore. The one meaningful exception is direct like-for-like device replacement — swapping a broken outlet, switch, or fixture on an existing circuit.
Only an Oklahoma Construction Industries Board (OCIB) licensed electrical contractor or a homeowner on their own owner-occupied residence may pull a Moore electrical permit. The licensed electrician of record is personally accountable for the inspection pass / fail. Moore does not issue a separate local trade license; OCIB licensing is sufficient.
Who needs this permit
Is this permit required for your Moore project?
Any OCIB-licensed electrical contractor performing service installs, panel upgrades, new circuits, sub-panels, generator interconnects, solar interconnects, EV charger circuits, or service reconnections in Moore. Homeowners may pull permits on their own owner-occupied single-family residence.
Moore cost range
Expected permit fees in Moore
Moore electrical permits are simple flat fees. Service change or upgrade: $40. New residential service: $60. Other electrical work: $40 base + $1 per outlet / fixture, capped at $150. A typical residential rough-in for a 2,500 sq ft addition runs $70-$120 in Moore (low compared to OKC). Commercial electrical scales with rough-in count and load.
Fees reference the current Moore Community Development fee schedule. Contact (405) 793-5053 to confirm for your specific project valuation.
Required documents
What Moore Community Development needs from you
- Moore electrical permit application (online via mooreok.govbuilt.com or paper at City Hall)
- Active OCIB electrical contractor license number (verify at cib.ok.gov)
- Load calculation for service upgrades or any project adding more than 40A of new load
- Single-line diagram for commercial work and any residential service over 400A
- Property address and linked parent building permit number if applicable
- For solar / PV: signed utility interconnection agreement with OG&E or OEC
- For EV charger: circuit calculation and panel directory update
Process & timeline
Step-by-step process in Moore
- 1
Pull the permit — usually same day online if the electrician is set up in GovBuilt.
- 2
Rough-in inspection BEFORE drywall or any concealment. Failure rate here is the highest of any Moore electrical inspection.
- 3
Service / meter inspection coordinated with OG&E (Oklahoma Gas & Electric) or OEC (Oklahoma Electric Cooperative) for new service sets.
- 4
Final inspection after devices, covers, and panel directory are installed.
- 5
Typical total clock time: 2-4 weeks on a residential project depending on rough-in / final trade sequencing.
Common reasons for rejection
Why Moore rejects electrical permit applications
- Rough-in scheduled before boxes are secured, staples set within 8 inches of boxes, or ground conductors made up
- Missing AFCI / GFCI protection in required locations (every bedroom, kitchen, bath, garage, exterior, basement per 2017 NEC)
- Panel directory blank or illegible at final
- Tamper-resistant receptacles missing in dwelling units
- Working clearance in front of service panels blocked by shelving or stored material
- Grounding electrode conductor not bonded to building steel or water service where required
- OCIB license expired or not listed on the application
Skip the rejection cycle on your Moore electrical permit
Permitly analyzes your project against Moore Community Development requirements and generates a pre-filled application packet in under 3 minutes. First analysis is free.
Moore Community Development: (405) 793-5053 · 301 N Broadway Ave, Moore, OK 73160
Electrical permit FAQs — Moore, OK
Do I need a permit to install an EV charger in Moore?
Yes. A Level 2 (240V) EV charger requires a dedicated circuit, which requires a Moore electrical permit pulled by an OCIB-licensed electrician. Level 1 (120V plug-in) using an existing outlet does not. Permit fee runs $40-$60.
Can I pull an electrical permit as a homeowner in Moore?
Yes, on your own owner-occupied single-family home. The inspection standard is identical to licensed-contractor work. You sign an affidavit acknowledging code-compliance responsibility.
How much is a service panel upgrade permit in Moore?
Service panel upgrade or service change: $40 flat. New residential service: $60. The OG&E or OEC meter set coordination is handled separately by the utility.
Related Moore permits
Building Permit
Moorerequirements, cost & process
Mechanical Permit
Moorerequirements, cost & process
Tornado Safe Room / Storm Shelter Permit
Moorerequirements, cost & process
Commercial Tenant Improvement Permit
Moorerequirements, cost & process